Specs: Firmware: Latest Version (support firmware upload) Continuous current: single 100A, dual 200A; instantaneous current: single 400A, dual 800A Voltage: 14V-60V(Cells: 4-13S; safe for 4S to 12S, voltage spikes may not exceed 60V! ) BEC: 5V@1.5A ERPM: 150000 Control Interface Ports:USB,CAN,UART, SPI, IIC (for IMU) Supported Sensors:ABI，HALL，AS5047，AS5048A Input Set Support:PPM, ADC, NRF, UART Modes: BLDC, FOC (sinusoidal) Regenerative capacity: Yes Programmable: Yes Both sensored/ sensorless motor: Yes Motor wire: 12AWG Power cable:8AWG Size: 81 x 77 x 20 mm(Including heatsink) Feature: Support four control modes: Current/Dutycycle/Speed /Position control mode. Using 12pcs JMSL0601AG high current MOSETS. Protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection. Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050,LSM6DS3, BMI160. Wiring diagram:

Lesen Sie Mehr Weniger

Specification: Model: Flipsky External UBEC 20S 20A  Main Battery Input Voltage: 4-20S Lipo Output Voltage: 5.0V (default) / 6.0V / 7.4V / 8.4V (4-10V adjustable by rotating calibration switch on the rear) Output Current: Continuous 20A (duration time depends on external heat dissipation conditions) Size: 60.4*47.15*28.2mm Weight: 114g Feature:  1.Metal shielding cover for good heat dissipation and reducing electromagnetic interference. 2.High efficiency DC-DC voltage regulator chip for transfer efficiency over 90%. 3.Sustained output current up to 20A (depends on external heat dissipation conditions). 4.Main power input available 4-20S Lipo. Adjustable output voltage (4-10V) compatible with different voltages. 5.Various protections like over-current protection, output short circuit protection, overheating protection and low voltage cutoff. Usage Guide: Wiring Diagram: If there is a built-in BEC in the brushless ESC, please disconnect the ESC's BEC output wires (e.g. “5V” and “GND” as shown below). Connect the signal wire “S” to the receiver's ‘S’ channel at the interface. Then, connect the UBEC's input wires in parallel with the battery pack. Plug the output terminals into the receiver's “+” and “-” channels. Voltage Output Adjustment: Adjustable output voltage (4-10V) in four levels through the calibration switch on the rear. The factory default voltage is 5.0V, shown as below: Front View: Rotating the potentiometer clockwise to reduce the output voltage; rotating it counterclockwise to increase the output voltage.

Lesen Sie Mehr Weniger

Specifications :  Firmware: V1.5 and above (firmware update via Flipsky ESC Tool supported)Voltage: 14V-85V (safe for 4S-20S)Continuous current: 50V/400A; 75V/350A; 85V/300A (Values depend on the mounting, ambient temperature and air/water circulation around the device.)Peak Current: 800ABEC: 5V@1APower/Motor Wires: Integrated M6 terminalsProgrammable Tool: Flipsky ESC TOOLPWM Frequency Control: YESMultiple Speed Gear Limit Control: YES (UART / ADC)Regenerative Capacity: YESCommunication Ports: USB, CAN, UART, PPM, ADC/PASInput Signals Support: PPM, ADC, PAS, UART(compatible with FLIPSKY remote such as VX1, VX1Pro, VX2, VX3, VX3Pro, VX4Pro )Startup Modes Support: IPDS (sensorless), HFPI (sensorless), HALL (sensored), ENCODER(ABI Encoder，AS5047 Absolute Type Encoder SPI Port), OPEN(Sensorless Open-Loop Startup)Traction Control: YESMultiple Speed Gear levels: Low, Medium, High, ReverseSwitch Support: Power on/off button switch or key switchSize:L190*W109.1*H55.8(with aluminum enclosure) Features: 1.Adopting ARM Cortex-M4 structure with the max 240MHz , improves PWM switching frequency and the motor RPM.2.Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different battery voltages and multiple control methods.3.Programmable via Flipsky remote controller VX4Pro(remote firmware version: VX4Pro_V1.1 and above)4.Supporting motor FOC with low working noise and smooth starting.5.Supporting Real-time data and fault alerts.6.Supporting adaptive variable PWM frequency control.7.Supporting sensor mode(HALL,ENCODER) and sensorless mode(IPDS, HFPI,OPEN).8.Supporting control types: Current, Duty Cycle, Speed Control, Position Control.9.Supporting multiple types of motor temperature sensors such as NTC-10k-25℃, NTC-10K-100℃, PT1000, PTC-1K-100℃, KTY, etc.10.Protection functions: low and high voltage protection, motor over-temperature protection, MOSFET over-temperature and over current protection, battery over discharge protection.11.Integrating power of 12V(3pcs) to provide power for external devices(headlight, brake light, horn, etc.) with two groups normally open and one controlled by brake signal. (Note: maximum output current:4A)12.Supporting brake signal to cut off ESC output. Wire Connection:

Lesen Sie Mehr Weniger

Specifications: Model: Anti-spark Switch Smart V3.0 Working Voltage: 6-20S Li-Po Output Current: Continuous max 300A (duration time depends on external heat dissipation conditions) Diameter of Switch Button: 12mm (Self-lock switch) Size: 97*57*24mm Weight: 311g Features: 1.Metal shielding cover for good heat dissipation and reducing electromagnetic interference. 2.Equipped with LED indicator light, users can check the status of the light to determine whether it works normally. 3.If the light is always on, indicating the switch works normally. If the light flashes indicates that the short-circuit protection function has been triggered. 4.Soft start-up: Increasing the current / voltage in the circuit slowly to achieve smooth load start-up. It can reduce the impact of start-up, protecting the load, switch and the entire circuit system and improve safety. 5.Support start-up short circuit protection, working short circuit protection, preventing the controller and power supply system damage effectively, which improves the liability and safety of equipment. Wire Connection:

Lesen Sie Mehr Weniger

Specifications:   Weight 0.84KG   Max Power 2700W Motor KV 140190 Max current 75A Battery type 4-14S Recommend ESC VESC6 Max Torque 7.5Nm Diameter(mm) 63 Length(mm) 68 Total length (mm)92mm Shaft(mm) 10mm Dshaft Bullet connector 4mm   Wire configuration   Blue = U White = V Yellow = W BLDC Motor

Lesen Sie Mehr Weniger

Speciation: Size:L107mm*W103mm*H18.5mmVoltage:14-84V (4-20S safey)Current:continuous max 100A single,dual continuous max 200A,values depend on the mounting  and ambient temperature around the device!BEC:5V@1ASupport BLDC square wave mode control and FOC sine wave modeFirmware: latest (firmware update supported)ERPM:150000Control Interface Ports:USB,CAN,UARTSupported Sensors:ABI，HALL，AS5047，AS5048AInput Set Support:PPM，ADC，NRF,UARTWire Size: 12AWGProgrammable: YesRegenerative Capacity: Yes Warm tips: Phase filering is not available for Flipsky ESC75100 and 75200!Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface. Wire Connection:

Lesen Sie Mehr Weniger

Specs: 75100: 75100 Pro: Size: L103mm*W58mm*H27.7mm Voltage:14-84V (4-20S) Current:100A Continuous,burst 120A BEC:5V@1.5A Support BLDC square wave mode control and FOC sine wave mode Firmware: latest (firmware update supported) ERPM:150000 Control Interface Ports:USB,CAN,UART Supported Sensors:ABI，HALL，AS5047，AS5048A Input Set Support:PPM，ADC，NRF,UART Wire Size: 10AWG(75100 Pro) Programmable: Yes Regenerative Capacity: Yes Newly upgraded: Change connection wires from 12Awg to 10Awag. More sensitive temperature detection function Integrated bluetooth module design Size & design upgraded Warm tips: Phase filering is not available for Flipsky ESC75100 and 75200!Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface.Here below video and blog links FYI. Wire Connection: 75100: 75100 Pro:

Lesen Sie Mehr Weniger

Spec: Firmware: 6.02 (firmware update supported) Size: L103mm*W58mm*H27.7mm Voltage:14-84V (4-20S) Current:100A Continuous BEC:5V@1.5A Support BLDC square wave mode control and FOC sine wave mode ERPM:150000 Control Interface Ports:USB,CAN,UART Supported Sensors:ABI，HALL，AS5047，AS5048A Input Set Support:PPM，ADC，NRF,UART Wire Size: 10AWG(75100 Pro) Programmable: Yes Regenerative Capacity: Yes Phase Filter: Yes Power Switch Button: Red integrates Bluetooth module function The maximum peak current is 150A the absolute maximum current is recommended to be set to 200A Wiring diagram: Instruction manual for 75100 Pro V2.0

Lesen Sie Mehr Weniger

Specication: Size: 103X58X24mmVoltage:14-84V (4-20S)Continuous Current: 100APeak Current: 250AFirmware: 5.02; firmware upgrade available (Phase filter needs to be turned off for firmware 5.03 or newer)BEC: 5V@1AModes: DC，BLDC，FOC(sinusoidal)Control Interface Ports: USB,CAN,UARTSupported Sensors: ABI，HALL，AS5047，AS5048AInput Set Support: PPM，ADC，NRF,UARTWire Size: 12AWGProgrammable: YesRegenerative Capacity: YesPower Switch Button: Red Wire Connection:

Lesen Sie Mehr Weniger

Specification: Wire Connection:

Lesen Sie Mehr Weniger

Warm tips: It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC. Specs: Firmware: 5.2, supports firmware upgradeVoltage: 14-84V (safe for 4-20S)Continuous current: 50V/200A; 75V/150A (Values depend on the mounting, ambient temperature and air/water circulation around the device!); Burst: 300ABEC: 5V@1ASupport Modes: DC, BLDC, FOC (sinusoidal)ERPM: 150000Communication Ports: USB, CAN, UART, SPI, IICSupported Sensors: ABI, HALL, AS5047, AS5048AInput Source Support: PPM, ADC, NRF, UARTSupported Sensorless: YesRegenerative capacity: YesProgrammable via VESC_TOOL: Yes75200 Size:130x67.7x40.1mm(Including alu. case)Motor/power wire size: 8 AWGFeatures:Adjustable protection against: low voltage protection, high voltage protection, over current protection, temperature abnormal protection, mosfets / motor over temperature protection.Support various control modes: Current / Duty cycle / Speed / PID control modes.Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160.CPU:32F405 with frequency 168MHzAluminum PCB with good heat dissipation to expand life span.Two COMM ports: UART bluetooth module, screen display or remote controller supportable. Warm tips: Phase filering is not available for Flipsky ESC75100 and 75200!Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface. Wire Connection:

Lesen Sie Mehr Weniger

Spec: Working Voltage: 6-20S Li-Po Output Current: Continuous max 300A (duration time depends on external heat dissipation conditions) Diameter of Switch Button: 12mm (Self-lock switch) Size: 97*57*24mm Weight: 311g Features: Metal shielding cover for good heat dissipation and reducing electromagnetic interference.  Equipped with LED indicator light, users can check the status of the light to determine whether it works normally.  If the light is always on, indicating the switch works normally. If the light flashes indicates that the short-circuit protection function has been triggered. Soft start-up: Increasing the current / voltage in the circuit slowly to achieve smooth load start-up. It can reduce the impact of start-up, protecting the load, switch and the entire circuit system and improve safety.  Support start-up short circuit protection, working short circuit protection, preventing the controller and power supply system damage effectively, which improves the liability and safety of equipment. Wiring diagram:

Lesen Sie Mehr Weniger