Flipsky 4-20S Lipo 20A External UBEC Output Adjustable 5.0V (default) / 6.0V / 7.4V / 8.4V For RC Car Fixed Wing Aircraft Robot

Beschreibung

Specification:
Model: Flipsky External UBEC 20S 20A 
Main Battery Input Voltage: 4-20S Lipo
Output Voltage: 5.0V (default) / 6.0V / 7.4V / 8.4V (4-10V adjustable by rotating calibration switch on the rear)
Output Current: Continuous 20A (duration time depends on external heat dissipation conditions)
Size: 60.4*47.15*28.2mm
Weight: 114g

Feature: 
1.Metal shielding cover for good heat dissipation and reducing electromagnetic interference.
2.High efficiency DC-DC voltage regulator chip for transfer efficiency over 90%.
3.Sustained output current up to 20A (depends on external heat dissipation conditions).
4.Main power input available 4-20S Lipo. Adjustable output voltage (4-10V) compatible with different voltages.
5.Various protections like over-current protection, output short circuit protection, overheating protection and low voltage cutoff.

Usage Guide:
Wiring Diagram:
If there is a built-in BEC in the brushless ESC, please disconnect the ESC's BEC output wires (e.g. “5V” and “GND”
as shown below). Connect the signal wire “S” to the receiver's ‘S’ channel at the interface. Then, connect the UBEC's
input wires in parallel with the battery pack. Plug the output terminals into the receiver's “+” and “-” channels.
Voltage Output Adjustment:
Adjustable output voltage (4-10V) in four levels through the calibration switch on the rear. The factory default voltage is 5.0V, shown as below:
Front View: Rotating the potentiometer clockwise to reduce the output voltage; rotating it counterclockwise to increase the output voltage.

Flipsky 4-20S Lipo 20A External UBEC Output Adjustable 5.0V (default) / 6.0V / 7.4V / 8.4V For RC Car Fixed Wing Aircraft Robot

Produkt Form

Specification: Model: Flipsky External UBEC 20S 20A  Main Battery Input Voltage: 4-20S Lipo Output Voltage: 5.0V (default) / 6.0V /... Lesen Sie mehr

SKU: FSUBEC20S20AC01

$23.89 Exkl. MwSt

    • Tell a unique detail about this product
    • Tell a unique detail about this product
    • Tell a unique detail about this product
    • Heute verschickt? Bestellung innerhalb: Oct 24, 2025 17:00:00 +0800

    Beschreibung

    Specification:
    Model: Flipsky External UBEC 20S 20A 
    Main Battery Input Voltage: 4-20S Lipo
    Output Voltage: 5.0V (default) / 6.0V / 7.4V / 8.4V (4-10V adjustable by rotating calibration switch on the rear)
    Output Current: Continuous 20A (duration time depends on external heat dissipation conditions)
    Size: 60.4*47.15*28.2mm
    Weight: 114g

    Feature: 
    1.Metal shielding cover for good heat dissipation and reducing electromagnetic interference.
    2.High efficiency DC-DC voltage regulator chip for transfer efficiency over 90%.
    3.Sustained output current up to 20A (depends on external heat dissipation conditions).
    4.Main power input available 4-20S Lipo. Adjustable output voltage (4-10V) compatible with different voltages.
    5.Various protections like over-current protection, output short circuit protection, overheating protection and low voltage cutoff.

    Usage Guide:
    Wiring Diagram:
    If there is a built-in BEC in the brushless ESC, please disconnect the ESC's BEC output wires (e.g. “5V” and “GND”
    as shown below). Connect the signal wire “S” to the receiver's ‘S’ channel at the interface. Then, connect the UBEC's
    input wires in parallel with the battery pack. Plug the output terminals into the receiver's “+” and “-” channels.
    Voltage Output Adjustment:
    Adjustable output voltage (4-10V) in four levels through the calibration switch on the rear. The factory default voltage is 5.0V, shown as below:
    Front View: Rotating the potentiometer clockwise to reduce the output voltage; rotating it counterclockwise to increase the output voltage.

    Recently viewed products

    Anmeldung

    Haben Sie Ihr Passwort vergessen?

    Sie haben noch kein Konto?
    Konto erstellen