Product Description-- Charging current: ≤10A Discharge current: 30A Internal resistance: ≤15mΩ Charging voltage:The number of Li-ion batteryin series connection X 4.2VWiring : Same Port   Overcharge protection—— Detection voltage: 4.25±0.025V Detection delay: 1000±500MS Release voltage: 4.15±0.05V Over-discharge voltage protection—— Detection voltage: 2.75±0.1V Detection delay: 1000±500MS Release voltage: 3.0±0.1V Balanced voltage—— Detection voltage: 4.15±0.025V Detection delay: 100±50MS Balance current: 42±5MA Over discharge current protection—— Detection voltage: 50±15MV Detection delay: 1000±500MS Current protection: 50±8A Short circuit protection-- Trigger condition: external short circuit Detection delay: 300us Release condition: disconnect the load Temperature control protection—— Charge and discharge over-temperature protection: 55℃ Charge and discharge high temperature release temperature: 75℃ Release condition:During normal working temperature Self-consumption—— Working power consumption: <35UA Over-discharge power consumption(Sleeping State): <10UA Operating temperature range: -30°~+80°C   Product Features-- Overcharge protection Over discharge protection Overcurrent protection Balanced protection Temperature control protection Applicablefor 4S-7S / 8S-14S Li-ion battery   Package—— 4S-7S: 1* 4-7S BMS PCBA board 1*HY2.0 single head 8P line Net weight:12.2g Weight:87g Size:47.6*32*9.2mm 8S-14S: 1* 8-14S BMS PCBA board 1*HY2.0 single head 7P line 1*HY2.0 single head 8P line Net weight:13.3g Weight:96g Size:47.6*32*9.2mm   ATTENTION—— 1. It is strictly forbidden to insert balance wires into BMS before connecting batteries.Must make sure that the cable is soldered correctly first , and then connect the BMS board. 2. The sequence of connecting wires for BMS: a.From thin black balance wire to stare, the 2ndwire(thin red wire)connect with the 1stbattery’s positive pole.Then connect each cell’s positive pole in order until the last one B+. b.Please do not insert the plug directly after the cable is connected.Measure the voltage between each two adjacent metal terminals on the back of the plug. If it is a ternary polymer battery, the voltage should be between 3.0 ~4.2V, and the voltage of the iron-lithium battery should be between 2.0 ~3.6V. The voltage should be between 1.5~2.75V. c.After confirming that the wiring sequence and voltage of the cables are correct, insert them into the socket of the protection board. Attentionplease: The cables of different manufacturers are not universal, please make sure to use the matching cables. 3. After the wiring is completed, measure whether the voltage of battery B+and B- ,andthe voltage of B-and C- are equal. If they are equal, the protection board is working normally and can be used normally. If it is not equal, please check the wiring again.

Read more less

MKBMS 4-14S_80A BMS board is a full-function Li-ion battery protection board with passive balance. The continuous current can reach to 80A. It supports overcharge protection, overcharge protection, over current protection, ,over temperature protection, short circuit protection, etc. Extensive evaluation of e-bike, e-skateboard,electric motorcycles, e-scooters, electric balance cars and other fields. Parameters:  Feature: Wiring : same port or different ports（When using the charging and discharging same port, disconnect the p-） Balance function, fully activate the battery capacity No need to adjust parameters, the operation is easier Metal heat sink, more stable performance With locking cable arrangement, the wiring is more secure Function: 1 .Over charge protection Over discharge protection Overcurrent protection Short circuit protection Temperature control protection Balanced protection Static protection Load detection function Application : Electric skateboard Electric bicycle Smart balance car Electric Scooter Forklift Cleaning car Sightseeing car Three-wheels car  Shipping list: 1X MKBMS（4/7/10/13/14）S 80A Li-ion BMS Board 1X GH2.0 single head（5/8/11/14/15）P line（with buckle） Operational matters: Please ensure the correctness of the wiring sequence during wiring.Please arrange the lines in order from B0-B14.After the battery is fully powered, the voltage will reach a maximum of 100V. There is a risk of electric shock, so please pay attention to protection.    

Read more less

Video: Only Charge Board does not support discharge protection, please do not discharge through this protection board. Specs: Type: Charge only Cell Chemistry: Li-ion (3.7V nominal) Balance method: Passive balance Series Count: 4S-24S Charge Current: 20A Overcharge Voltage: 4.25V Overcharge Reset: 4.19V Balance: 30-50mA@4.2V Overtemperature: 60°C Overtemperature Reset: 40°C Size: 110*30*11mm Net weight: 30g Package Included: 1* MKBMS 4S-24S 20A Only Charge Board 1* GH2.0 single head 12P line 1* GH2.0 single head 13P line 1* HY2.0 single head 2P cable with thermal protection switch 1* Charging cable with XT60 or XT30 connectors

Read more less

MKBMS 4S-30S 20A Only Charge Battery Protect Board device is designed to reduce the risk of charging. Designed to be ultra-compact and simple to use without any configuration required. Features high charging current, balancing activity LED lights, overcharge, and over temperature protection .Extensive Used in electric bicycles, electric scooters, Onewheels and other fields. MKBMS 4S-30S 20A Only Charge Board does not support discharge protection, please do not discharge through this protection board. adapter board: https://shorturl.at/bhjTY Specs: Type: Charge only Cell Chemistry: Li-ion (3.7V nominal) Balance method: Passive balance Series Count: 4S-30S Charge Current: 20A Overcharge Voltage: 4.25V Overcharge Reset: 4.19V Balance:20-30mA@4.2V（Please balance the battery first before charging） Overtemperature: 60°C Overtemperature Reset: 40°C Size: 130*30*11mm Net weight: 30g Features: Compact charge only design Cell balance indicator LED Compatible with 4s-30s battery Designed to be ultra-compact and simple to use without any configuration required Anodized aluminum heatsink case, stable performance Functions: Balance function Overcharge protection Overtemperature protection Cell balance indicator LED Common Uses: ▪ One-wheeled electric skateboards ▪ Electric Skateboards ▪ Electric Scooters ▪ Electric Bikes ▪ EUCs Package Included: 1* MKBMS 4S-30S 20A Only Charge Board 1* GH2.0 single head 15P line 1* GH2.0 single head 16P line 1* HY2.0 single head 2P cable with thermal protection switch 1* Charging cable with XT30 or XT60 connectors Operation Notes: Please ensure the correctness of the wiring sequence, from B0-B15, B16-B30, the voltage increases from low to high in sequence. This BMS is compatible with battery packs up to 30s, which is over 5V DC when fully charged. Electric shocks from high voltage may cause serious injury. Please pay attention to safety when using. This device is designed to reduce the risk of charging and will not protect against overcurrent discharge, undervoltage, internal pack shorts, pack overtemperature. Video:

Read more less

Description The 5-12S 200A MINI ESC is a high-performance brushless electronic speed controller (ESC) that supports 5-12S LiPo battery input and provides a continuous current rating of up to 200A. Designed for high-power applications, it is widely used in FPV racing drones, multi-axis UAVs, fixed-wing model aircraft, RC cars, RC boats, agricultural spraying drones, electric cruise UAVs, firefighting drones, and other industrial drone platforms. 5-12S 200A MINI ESC Specifications Type: Brushless Motor Electronic Speed Controller (ESC) Continuous Current: 200A Burst Current: 250A Weight: Net Weight 144g ± 5g Dimensions: 84mm (Length) × 43mm (Width) × 28mm (Height) Input Power: 5S–12S LiPo Battery Firmware Version: MAXKGO_12S_F421 Firmware Upgrade: Supports online firmware updates via AM32.ca Communication Protocols: Dshot300, Dshot600, Servo PWM Telemetry Feedback: The TX telemetry port supports ESC data feedback, including voltage, current, temperature, motor RPM, and other operating parameters BEC: No BEC output Cooling Fan: No built-in cooling fan Water Resistance: Not waterproof; only resistant to light splashes 5-12S200A MINI ESC Features Feature Category Description Compact Design MINI Size Protection Functions Supports multiple protection functions: Low-voltage protection, over-temperature protection, motor stall protection, low-speed protection MCU Performance High-performance ARM 32-bit Cortex-core MCU with an operating frequency of 120 MHz RC Car Support Stall protection for RC cars and crawlers Drone Protection Stuck rotor protection for multi-rotor drones Firmware Upgrade Firmware upgradable via Betaflight passthrough, single wire serial, or Arduino Web Configurator Web configurator at am32.ca Protocol Support Supports Dshot 300, Dshot 600 and Servo PWM communication protocol Telemetry Support EDT for full Dshot telemetry via signal wires Smooth Startup Sinusoidal startup mode for smoother starting on RC cars and crawlers 5-12S 200A MINI ESC Applications Multi-axis UAVs Fixed-wing model aircraft RC cars RC boats Agricultural spraying drones Electric cruise UAVs Firefighting drones Package Contents Package 1 5-12S 200A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) Package 2 5-12S 200A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) 3-Pin Dupont Cable × 1 (33cm) XT90 Male Connector × 1 Positive & Negative Power Wires × 1 (8AWG / 200mm)  

Read more less

5-12S 80A_ESC Description： 5-12S 80A ESC is a high-performance brushless electronic speed controller (ESC) that supports 5-12S LiPo battery input and delivers a continuous current rating of up to 80A. It is widely used in FPV racing drones, multi-rotor drones, fixed-wing aircraft, RC cars, RC boats, and other model applications.   5-12S 80A ESC Specifications Type: Brushless Motor Electronic Speed Controller (ESC) Continuous Current: 80A Burst Current: 100A Weight (without capacitor): Net Weight 19.2g ± 2g Dimensions: 46.4mm (Length) × 24.8mm (Width) × 9.6mm (Height) Input Power: 5S–12S LiPo Battery Firmware Version: AM32_MAXKGO_F421 Firmware Upgrade: Supports online firmware updates via AM32.ca Communication Protocols: Dshot300, Dshot600, Servo PWM Signal Feedback: The TX telemetry port supports ESC data feedback, including voltage, temperature, and motor RPM (current sensing is not supported) BEC: No BEC output Cooling Fan: No built-in cooling fan Water Resistance: Not waterproof; only resistant to light splashes 5-12S 80A ESC Features MINI Size, MAX Power OutputCompact design with high-performance power output, providing an excellent balance between size and performance. Multiple Protection Functions: Low Voltage Protection Over Temperature Protection Motor Stall Protection Low-Speed Protection Equipped with a high-performance ARM 32-bit Cortex-core MCU with a processing frequency of up to 120MHz. Designed with stall protection for RC cars and crawler vehicles to prevent damage caused by motor blockage. Provides propeller jam (stall) protection for multi-rotor drones, improving flight safety and ESC reliability. Supports firmware upgrades via: Betaflight Passthrough Single-wire UART Arduino Supports parameter configuration through the AM32.ca online configuration tool. Supports Servo PWM and Dshot300 / Dshot600 protocols. Supports EDT (Extended Dshot Telemetry), allowing full telemetry data transmission through the signal wire. Equipped with sine wave startup mode, providing smoother and more responsive startup performance for RC cars and crawler vehicles. 5-12S 80A ESC Applications Multi-rotor drones Fixed-wing model aircraft RC cars RC boats Package Contents Package 1 5-12S 80A ESC × 1 Heat Shrink Tubes × 5 Electrolytic Capacitor × 1 (63V 680μF) 2-Pin Dupont Cable × 1 (33cm) Package 2 5-12S 80A ESC × 1 Heat Shrink Tubes × 5 Electrolytic Capacitor × 1 (63V 680μF) 2-Pin Dupont Cable × 1 (33cm) 3-Pin Dupont Cable × 1 (33cm) XT90 Male Connector × 1 Black Power Wire × 1 (12AWG, 120mm) Red Power Wire × 1 (12AWG, 120mm)

Read more less

5-14S 100A ESC Description The 5-14S 100A ESC is a high-performance brushless electronic speed controller (ESC) that supports 5-14S LiPo battery input and provides a continuous current rating of 100A. It is widely used in FPV racing drones, multi-rotor UAVs, fixed-wing model aircraft, RC cars, RC boats, agricultural spraying drones, and other high-performance RC applications. 5-14S 100A ESC Specifications Type: Brushless Motor Electronic Speed Controller (ESC) Continuous Current: 100A Burst Current: 130A Weight: Net Weight 72g ± 5g Dimensions: 68.5mm (Length) × 34mm (Width) × 24.5mm (Height) Input Power: 5S–14S LiPo Battery Firmware Version: MAXKGO_V1_F421 Firmware Upgrade: Supports online firmware updates via AM32.ca Communication Protocols: Dshot300, Dshot600, Servo PWM Telemetry Feedback: The TX telemetry port supports ESC data feedback, including voltage, current, temperature, motor RPM, and other operating parameters BEC: No BEC output Cooling Fan: No built-in cooling fan Water Resistance: Not waterproof; only resistant to light splashes 5-14S 100A ESC Features Mini Size, Powerful PerformanceCompact design with high power output, providing excellent performance for various RC applications. Multiple Protection Functions: Low Voltage Protection Over Temperature Protection Motor Stall Protection Low-Speed Protection Equipped with a high-performance ARM 32-bit Cortex-core MCU with a processing frequency of up to 120MHz. Stall Protection for RC Cars and CrawlersHelps prevent ESC damage caused by motor blockage during low-speed or high-load operation. Stuck Rotor Protection for Multi-Rotor DronesProvides protection against propeller blockage or sudden motor stoppage during flight. Flexible Firmware Upgrade SupportFirmware can be upgraded through: Betaflight Passthrough Single-wire Serial Arduino AM32 Web Configurator SupportSupports online parameter configuration through AM32.ca. Multiple Protocol CompatibilitySupports: Servo PWM Dshot300 Dshot600 EDT (Extended Dshot Telemetry) SupportEnables full Dshot telemetry feedback through the signal wire for real-time ESC monitoring. Sinusoidal Startup ModeProvides smoother startup performance for RC cars and crawlers, reducing vibration and improving control response. 5-14S 100A ESC Applications Multi-rotor drones Fixed-wing model aircraft RC cars RC boats Package Contents Package 1 5-14S 100A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) Package 2 5-14S 100A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) 3-Pin Dupont Cable × 1 (33cm) XT90 Male Connector × 1 Positive & Negative Power Wires × 1 (10AWG / 200mm)

Read more less

Product DescriptionMAXKGO 5-16S 480A High Current Power Distribution Board The MAXKGO 5-16S 480A Power Distribution Board (PDB) is a high-performance power distribution solution designed for high-power FPV racing drones, multirotor drones, and large UAV platforms. Supporting 5S to 16S LiPo battery input and delivering up to 480A total continuous current (120A × 4 channels), this PDB provides stable and efficient power distribution for demanding drone applications. Designed with a lightweight structure and high-current capability, it features a 6-layer PCB with 3oz copper layers, ensuring excellent current handling performance and improved reliability during high-load operation. The board integrates dual BEC outputs (5V and 12V), allowing direct power supply for flight controllers, cameras, receivers, and other onboard electronics. Key Features Ultra High Current Capability Supports 5S-16S LiPo battery input Total continuous current: 480A 4-channel output design: 120A continuous current per channel 130A peak current per channel Dual BEC Power Output Built-in dual voltage BEC outputs: 5V / 3A output 12V / 3A output Suitable for powering: Flight controllers FPV cameras Video transmitters Other onboard electronics High-Performance PCB Design 6-layer PCB structure 3oz copper layers for excellent current capacity Lightweight design with only 17.7g net weight Compact size for easy installation Multiple ESC Support Supports up to 8 ESC connections, making it suitable for larger multirotor platforms. Technical Specifications Item Specification Product Type High Current Power Distribution Board Battery Input 5S-16S LiPo Input Voltage Range 15V-68V Continuous Current 480A Total (120A × 4) Peak Current 130A per channel BEC Output 1 5V / 3A BEC Output 2 12V / 3A ESC Support Up to 8 ESCs PCB Structure 6-layer PCB Copper Thickness 3oz Efficiency ≤95% Static Power Consumption 1mA Current Sensor Ratio 50 Communication Port 8-pin SH1.0 connector Mounting Hole Pattern 30.5 × 30.5mm Mounting Hole Diameter 4mm (M4) Dimensions 55 × 55 × 6.55mm Weight 17.7g Operating Temperature -20℃ to 100℃ Recommended Drone Size 8-16 inch Applications The MAXKGO 5-16S 480A PDB is ideal for: FPV Racing Drones Long-range FPV Drones Heavy-lift Multirotors Industrial UAV Platforms High-power Drone Builds Package Includes MAXKGO 5-16S 480A Power Distribution Board ×1 8-pin Dual Connector Cable ×1 Anti-vibration Rubber Balls ×5 M3 Nuts ×5 Power Cable (8AWG 120mm) ×1 XT90 Male Connector ×1 Capacitor 80V 560μF ×1 Heat Shrink Tubes ×2

Read more less

MAXKGO 5~6" FPV Drone Battery Strap for LiPo Batteries | RC Car Battery Tie Down Strap

Read more less

Expertly designed, the MAXKGO smart BMS 12S 60V 70A protection board is compatible with both VESC and FSESC® systems. This smart BMS provides superior protection and efficiency for Ebikes, Esk8s, Escooters, and more. With advanced features including VESC compatibility, this BMS ensures maximum performance for all your electric transportation needs. Firmware & software repositories are available click here： MAXKGO Tutorial on MAXKGO BMS settings with VESC Spec: Cell voltage operating range:2V-5V Recommended series cell:6S-12S Charge / discharge voltage:24V-52V Charge Current：≤20A Abs. Max battery voltage: 60V Minimum operating voltage: 14V Continuous charging current: 20A Over charge detect and release voltage: 2V-5V Over charge protection delay: ≥4ms Discharge current: ≤70A Max. Continuous discharge / regen current: 70A  Over discharge detect / release voltage: 0-5V Over current detect delay:≥4ms Discharge over current protection release condition: off load Short Circuit detect voltage:short circuit of external load Short Circuit detect delay: 320us Short Circuit protection release: off load Battery pack capacity and internal resistance detection: Yes Balance current: 86mA @4.2V Temp Protect: -20℃—+120℃ Working Temp Range:-20℃—+80℃ Storage Temp Range: -20℃—+100℃ Working current: ≤40mA Sleeping current: ≤100uA Size: 89 x 40 x 20.8mm Net weight: 106.5g Packing size: 140 x110 x 50 mm Package weight: 303.5g Including outer carton size: 170*120*100mm Weight with outer carton: 380g Feature: Compact layout and mini Using aluminum alloy material shell, better heat dissipation. Automotive grade design, automotive grade locking connector. Configuring and firmware upgrades over USB through the MAXKGO-BMS-TOOL and ENNOID-BMS-TOOL. Automotive grade monitoring & balancing IC with separate power supply for increased reliability Voltages measurements for load, charger & battery pack Bi-directional current monitoring SOC based on coulomb counting Humidity sensor & board temperature monitoring Charger detection circuit Integrated precharge circuit Power button, USB-C, UART, I2C & isolated CAN bus interface On board High-Efficiency 3.3V regulator powered from the main battery pack High current capacity automotive grade screw connectors for main power connections Buzzer & status LED Support:  overcharge/discharge/over current /temperature protection,and have thermal management/balance function(active balance and passive balance). Support:  almost all lithium batteries such as lithium ion battery, lithium polymer battery, lithium phosphate battery, etc. Packing list: 1* PCBA 1* HY2.0 single head 10P line 1* HY2.0 single head 13P line 2* GH1.25 single head 5P cable 1* GH1.25-5P to Dupont line 1* USB cable type-C data cable 1* 2.0MM jumper cap 1* 1.3 inch OLED display LCD screen module 1* 12MM 3-6V key switch 4* M5*8 stainless steel round head screws 4* M5 copper gasket 4* 90 degree angle terminal block T90-6/5  1* XT30 (female) Video: If you need more diagrams for different series, please contact us!

Read more less

Specification: Charging Voltage: 6*4.2VCharging Currect: 15ACharging Overcurrent Protection Value: 26ABalance Enable Voltage: 4.125VBattery Balance Current: 25 ± 5mAOvercharge Detection Voltage: 4.25 ± 0.05VOvercharge Release Voltage: 4.15 ± 0.05VDischarge Current: 30ADischarge Overcurrent Protection Value: 66AOver-discharge Detection Voltage: 2.8 ± 0.05VOver-discharge Release Voltage: 3.0 + 0.05VOver-discharge Detection Delay: 1Sshort Circuit Detection Delay: 200-500 μS (The actual results are subject to the customer's return and inspection)Working Temperature Range: -30°C~70°CStorage Temperature Range: -40°C~125°CTemperature Protection: Charging: -10°C~50°C, Discharging: -30°C~70°C (can be customized)Sleep Current (Battery Over-discharge): 10μA

Read more less

MAXKGO 6S-12S 100A  Smart Bluetooth BMS is a Lithium battery protection board with a discharge current of up to 100A. It has charge and discharge overvoltage/overtemperature  overcurrent/short circuit/Disconnection protection function. The product has UART/ CAN communication interface, and can be connected to Bluetooth mobile phone APP and computer BMS-TOOL. It is widely used in Ebicycles/Escooters/Ebalance cars/water electric products.ETC Specs:   Type:Smart BMS Board Cell Chemistry: Li-ion (3.7V nominal) Balance method: Passive balance Series Count: 6S-12S Charge Current: 15A Discharge current:100A Cell voltage operating range: 2v-5v Balance: 42mA@4.2V Shutdown Consumption: <100uA Temp detection channe: 5 NTC Voltage support range: 15V-51V Abs. Max battery voltage: 60V Charge protection Temp: 0°C~100°C Discharge protection Temp: 0°C~100°C Recommended Working Temp:-20°C~+75°C Size: 93.4mm*42.5mm *19.3mm   weight: 116.4g Features: 1. With Discrete BMS TOOL and mobile phone APP 2. Compatible with VESC CAN Port communication protocol 3. Compatible with VESC-TOOL 4. Bluetooth APP communication 5. Real-time Voltage/current/temperature/power monitoring 6. Connect the charger autostart,Fully charged/Unplug the charged autooff 7. Passive Balance Optional activation 8. Support series cell:6S-12S 9. Anodized aluminum heatsink case , stable performance 10. OLED displays various parameters in real time Functions:  1. Balance function 2. Overcharge protection 3. Overtemperature protection 4. CAN Port communication 5. UART communicatiion 6. BLUETOOCH 7. OLED display 8. Button on/off  Common Uses: ▪ Electric bicycle ▪ Electric Skateboards ▪ Electric Scooters ▪ Electric Bikes ▪ Water electric products ▪ EUCs Package Included: 1* MKBMS 6S-12S Smart Bluetooch BMS Board(With aluminum shell) 1* Bluetooth module 1* UART module 1* 1.3 inch OLED display LCD screen module 1* 12MM 3-6V push button switch 2* GH1.5 single head 5P line 1* GH1.25-5P to Dupont line 1* PH2.0 single head 13P line 1* PH2.0 single head 10P line 5* NTC 100K 4250B Thermistor Operation Notes: Please ensure the correctness of the wiring sequence, from B0-B12, the voltage increases from low to high in sequence. This BMS is compatible with battery packs up to 12s, which is over 50.4V when fully charged. Electric shocks from high voltage may cause serious injury.Please pay attention to safety when using.

Read more less