Specs:Firmware: 6.05 (or above in the future)Voltage: 14-110V (safe for 4-26S)Continuous current: 110V/300A (Values depend on the mounting,ambient temperature and air/water circulation around the device!); Burst: 800ABEC: 5V@3ASupport Modes: BLDC, FOC (sinusoidal)ERPM: 150000Communication Ports: USB, CAN, UART, SPI, IICSupported Sensors: ABI, HALL, AS5047, AS5048AInput Source Support: PPM, ADC, NRF, UARTSupported Sensorless: YesRegenerative capacity: YesProgrammable via VESC_TOOL: YesSize: 183.8*80.2*43.8mmMotor/power wire size: 8AWGPhase Filter: YesPower Switch Button: RedFeature:Adjustable protection against: low voltage protection, high voltage protection, over current protection, temperature abnormal protection, mosfets / motor over temperature protection.Support various control modes: Current / Duty cycle / Speed / PID control modes.CPU: SMT32F405 with frequency 168MHzDesign with Aluminum PCB with good heat dissipation to expand life span.FSESC110300 with aluminum pcb: supports serial port function,and built with powe on/off switchWiring diagram:

Read more less

Specifaction: Voltage:14-84V( safe for 3-20S)Continuous Current : 50V/300A,75V/200AMax Current :350ASupported sensors: ABI, HALL, AS5047,AS5048AEPRM:150000Size:297*115*45mm((Including the height of water pipes and electrolytic capacitors) Feature: Regenerative brakingThe CPU adopts the 32F405 with the main frequency of 168MHz and the Cortex-M4 architecture with DSP function;Sensored or sensorless operation + hybrid modeConfigurable RPM-, current-, voltage- and power limitsInput source: PPM, ADC, NRF,UART,PASCommunication ports: USB, CAN, UART,SPI,IICThrottle curve and ramping for all input sourcesSeamless 4-quadrant operationMotor revolution, ampere hour, watt hour countingReal-time data analysis and readout through the communication port.Adjustable protection against:Low input voltageHigh input voltageHigh motor currentHigh input currentHigh regenerative braking current (separate limits for the motor and the input)High RPM (separate limits for each direction)Digital VCC and analog VCC are produced by different voltage regulators respectively to make the system AD conversion more accurateMotor wire: 8AWGPower cable: 8AWGWaterproof level(with water cooling enclosure):IP67 Wire Connection:

Read more less

Specifications: Voltage:14-84V( safe for 3-20S) Continuous Current : 50V/350A,75V/250A Max Current :800A Supported sensors: ABI, HALL, AS5047,AS5048A EPRM:150000 Size:200*94.6*50mm((Including the height of water pipes and electrolytic capacitors) Warm tips: Phase filering is not available for Flipsky ESC75100 and 75200 ! Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface. Feature: 1.Regenerative braking 2.The CPU adopts the 32F405 with the main frequency of 168MHz and the Cortex-M4 architecture with DSP function; 3.Sensored or sensorless operation + hybrid mode 4.Configurable RPM-, current-, voltage- and power limits 5.Input source: PPM, ADC, NRF,UART,PAS 6.Communication ports: USB, CAN, UART,SPI,IIC 7.Throttle curve and ramping for all input sources 8.Seamless 4-quadrant operation 9.Motor revolution, ampere hour, watt hour counting 10.Real-time data analysis and readout through the communication port. 11.Adjustable protection against: 12.Low input voltage 13.High input voltage 14.High motor current 15.High input current 16.High regenerative braking current (separate limits for the motor and the input) 17.High RPM (separate limits for each direction) 18.Digital VCC and analog VCC are produced by different voltage regulators respectively to make the system AD conversion more accurate. 19.Motor wire: 8AWG 20.Power cable: 8AWG 21.Waterproof level(with water cooling enclosure):IP67 Wire Connection:

Read more less

Specs: Firmware: 5.2, supports firmware upgrade Voltage: 14-84V (safe for 4-20S) Continuous current: 50V/450A; 75V/350A (Values depend on the mounting, ambient temperature and air/water circulation around the device!); Burst: 1200A BEC: 5V@1A Support Modes: DC, BLDC, FOC (sinusoidal) ERPM: 150000 Communication Ports: USB, CAN, UART, SPI, IIC Supported Sensors: ABI, HALL, AS5047, AS5048A Input Source Support: PPM, ADC, NRF, UART Supported Sensorless: Yes Regenerative capacity: Yes Programmable via VESC_TOOL: Yes Red Switch Button: Yes Phase filter: Yes Size:227.5*140*54mm(Including Water Cooling Enclosure) Features: Adjustable protection against: low voltage protection, high voltage protection, over current protection, temperature abnormal protection, mosfets / motor over temperature protection. Support various control modes: Current / Duty cycle / Speed / PID control modes. Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160. CPU:STM32F405 with frequency 168MHz Aluminum PCB with good heat dissipation to expand life span. Built with ignite power on/off switch button. Wiring Diagram:

Read more less

Specifications:Firmware: V1.6 or above (firmware update via Flipsky ESC Tool supported)Voltage: 14-110V(safe for 4-26S)Continuous current: 100A (Values depend on the mounting, ambient temperature and air/water circulation around the device!)Peak Current: 250ACommunication Ports: USB, CAN, UART, PPM, ADC, PASInput Signals Support: PPM, ADC, PAS (Cadence Input Signal), UART (compatible with all Flipsky VX Series remotes)BEC: 5V@1AProgrammable Tool: Flipsky ESC TOOLPWM Frequency Control: YESMultiple Speed Gear Limit Control: YES (UART&ADC)Regenerative Capacity: YESIntegrated Self-locking Switch: 16mm Red ButtonMotor/power wire size: 10 AWGSize: L117.7*W62.4*H21.7mm (Including Alu. Case)Feature:Adopting ARM Cortex-M4 structure with the max 240MHz , improves PWM switching frequency and the motor RPM.Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different battery voltages and many control ways.Programmable via Flipsky VX4Pro remote (remote firmware version: VX4 Pro_V1.2 or above).Supporting motor FOC with low working noise and smooth starting.Supporting real-time data and fault alerts.Supporting adaptive variable PWM frequency control.Supporting save / load configuration files via ESC Tool.Supporting multiple speed levels: Level 1 (Low), Level 2 (Medium), Level 3 (High), Level 4 (PAS Only), Level 5 (PAS Only).Supporting sensor mode (HALL, ENCODER) and sensorless mode (IPDS, HFPI, OPEN).Startup Modes Support: IPDS (sensorless), HFPI (sensorless), HALL (sensored), ENCODER (such as ABI Encoder, AS5047 SPI, TLE5012 SPI, AS5600 IIC), OPEN (Sensorless Open-Loop Startup)Traction Control: YESSupporting control types: Current, Duty Cycle, Speed control, Position Control.Supporting PAS cadence sensor.Supporting emergency stop and shutdown.Support safe power-on protection (in PPM&ADC control modes only).Protection functions: low and high voltage protection, MOSFET over-temperature and over current protection, battery overcharge and discharge protection, motor over-temperature protection.Supporting multiple typed of motor temperature sensors such as NTC-10K-25℃ , NTC-10K-100℃ , PT1000, PTC-1K-100℃ , KTY and so on.Application Fields:Electric skateboard / Ebike / E-Scooter / Electric Motorc ycle / Robotics / FPV / RC Toys / Boat / Kayak etc.Wiring diagram:

Read more less

Specs： Hardware:V4.20Firmware:Latest VersionCurrent:50A continuous/single, 100A continuous/dual , Instantaneous current 150A per single, total 300A for system instantaneous current.Voltage: 8V-60V (Cells: 3-13S LiPo,Safe for 3S to 12S LiPo，Voltage spikes may not exceed 60V! )ERPM:60000BEC: 5V@1.5ABEC type: Internal driver support Modes: DC, BLDC, FOC (sinusoidal)Timing: Software calibration Cutoff Voltage: ProgrammableFrequency: PWM input Governor: NoProgramming card: NoReverse: YesMotor wire: 12AWG Power cable: 12AWG Package Contents:  1*Dual FSESC4.20 + Heatsink2*VESC Sensor Wires1*Micro USB 1*Manual Wire Connection:

Read more less

Specs:  Hardware:V4.20 Firmware: Latest Version Amps: 50A continuous / 150A peak Cells: 3-13S LiPo Voltage: 8V-60V BEC: 5V@1.5A BEC type: Internal driver support Timing: Software calibration Cutoff Voltage: Programmable Frequency: PWM input Governor: No Weight: 80g PCB Size: 39x46x17.4mm Size:67 x39x18.3mm(Include Heatsink) Programming card: No Reverse: YesMotor wire: 12AWGPower cable:12AWGWarm tips: please do not remove the shrink to protect the pcb electronics components from impurites or metals which result in short circuit or esc burnt damage. Package contains: 1*Mini FSECS4.20+ Heatsink1* Micro USB 1* VESC Sensor Wire1* Manual Wire Connection:

Read more less

Specs: Firmware: Latest Version Continuous current: 70A; instantaneous current: 200A Voltage: 14V-60V(Cells: 4-13S; safe for 4S to 12S, voltage spikes may not exceed 60V! ) BEC: 5V@1A ERPM: 150000 Control Interface Ports:USB,CAN,UART Supported Sensors:ABI，HALL，AS5047，AS5048A Input Set Support:PPM, ADC, NRF, UART, SPI, IIC Modes:DC, BLDC, FOC (sinusoidal) Regenerative capacity: Yes Programmable: Yes Motor wire: 12AWG Power cable:12AWG Size:67x39x18.7mm(Including heatsink) Feature: Support four control modes: Current/Dutycycle/Speed /Position control mode. Protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection. Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160. Wiring diagram:

Read more less

Specifications: Voltage Range: 6-14S(25.2-58.8V)Rated Current: 30A ; Max Current: 60ARated Power: 1200W ; Max Power: 2400WRated Torque: 2.0N·m ; Max Torque: 4.0N·mInternal Structure: 12N/4pThrust F/kgf (48V/30A): 18.3Thrust F/kgf (48V/60A): 27Resistance: 123mΩInductance: 220μHThree-phase leads: 3*12AWG (4.5mm)Insulation current: AC600V/10mA/3sPlug: 4mm Banana Plug (male)Shaft specification: Φ10-0.007Waterproof level: IP68

Read more less

Specification: Firmware: V1.6 and above (firmware update via Flipsky ESC Tool supported) Voltage: 14V-85V (safe for 4-20S) Continuous Current:85V/150A (Values depend on the mounting, ambient temperature and air/water circulation around the device.) Peak Current: 250A BEC: 5V@1A Power Wire: 8 AWG (1200mm) Motor Wire: 8 AWG (195mm) Programmable Tool: Flipsky ESC TOOL PWM Frequency Control: YES Multiple Speed Gear Limit Control: YES (UART） Regenerative Capacity: YES Communication Ports: USB，CAN，UART，PPM，ADC Control Signals Support: PPM，ADC，UART (compatible with all FLIPSKY VX Series remotes) Size: L93.8mm*W63mm*H26mm (with aluminum enclosure) Feature: 1.Fully sealed with lP68 water-proof rate. 2.Adopting ARM Cortex-M4 structure with the max 240MHZ,improves PWM switching frequency and the motor RPM. 3.Programmable via Flipsky ESC Tool to be compatible with multi-types of motors, different battery voltages and multiple control methods. 4.Programmable via Flipsky remote controller VX4Pro(remote firmware version: VX4Pro_V1.2 and above). 5.Supporting motor FOC with low working noise and smooth starting. 6.Supporting save / load configuration files via ESC Tool. 7.Supporting adaptive variable PWM frequency control. 8.Supporting real-time data and fault alerts. 9.Supporting multiple speed levels: Level 1 (Low), Level 2 (Medium), Level 3 (High). 10.Supporting Sensorless Mode: IPDS, HFPI, OPEN. 11.Startup Modes Support: IPDS (sensorless), HFPI (sensorless), OPEN (Sensorless Open-Loop Startup). 12.Traction Control: YES. 13.Supporting control types: Current, Duty Cycle, Speed Control. 14.Supporting emergency stop and shutdown. 15.Support safe power-on protection (in PPM&ADC control modes only). 16.Protection functions: low and high voltage protection, MOSFET over-temperature and over current protection, battery overcharge and discharge protection. Wire Connection:

Read more less

Specifications: Firmware: V1.4 or above (firmware update via Flipsky ESC Tool supported) Voltage: 14V-60V (safe for 4S-12S) Continuous Current: 60A / Single; 120A / Dual (Values depend on the mounting and ambient temperature around the device) Peak Current: 150A / Single; 300A / Dual Communication Ports: USB, CAN, UART, PPM, ADC Input Signals Support: PPM, ADC, UART (compatible with FLIPSKY remote VX4 and VX3Pro only at present), PAS Startup Modes Support: IPDS (sensorless), HFPI (sensorless), HALL (sensored), Encoder (ABI, AS5047 encoder SPI interface) BEC: 5V@1A Multiple Speed Gear Levels: Low, Medium, High, Reverse Front Lights, Rear Brake Lights & Horn: Support Programmable: Yes Regenerative Capacity: Yes Slide Poweron & Auto shutdown: Yes. Auto poweroff time can be customized. Self-resetting switch with green LED button Diameter: 16mm Power Wire Size: 12AWG; Motor Wire Size: 12 AWG Size: L85*W70*H25mm (including heatsink) Features: 1.Adopting CPU AT32F403ARCT7 with the structure of ARM Cortex-M4 allows CPU clock speed. 2.240MHz and the max PWM switching frequency 25KHz improves the motor RPM. Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different battery voltages and many control ways. 3.Programmable via Flipsky remote controller VX4 (remote firmware version: VX4_V1.4.0 or above). 4.Supporting motor FOC with low working noise and smooth starting. 5.Supporting Real-time data and fault alerts. 6.Supporting adaptive variable PWM frequency control. 7.Supporting sensor mode(HALL) and sensorless mode(IPDS, HFPI). 8.Supporting control types: Current, Duty Cycle, Speed control, Position Control. 9.Protection functions: low and high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature and over current protection, battery over discharge protecting, motor over-temperature protection. 10.Integrated smart switch function: supports sliding poweron and automatic shutdown function; automatic shutdown time is adjustable via Flipsky ESC Tool. 11.Supporting extra interface like front lights, brake lights and horn fixtures (12V 4A). 12.Supporting multiple typed of motor t emperature sensors such as NTC-10K-25℃, NTC-10K-100℃, PT1000, PTC-1K-100℃, KTY and so on. ​Wire Connection:

Read more less

Spec:Firmware supporting update via Flipsky ESC ToolVoltage: 14-84V(safe for 4-20S)Continuous current: 50V/60A; 75V/50A; 84V/40A (Values depend on the mounting, ambient temperature and air/water circulation around the device!); Peak Current: 250ACommunication Ports: USB, CAN, UARTInput Signal Support: PPM, UART(compatible with FLIPSKY remote VX4 only), ADCBEC: 5V@1AMultiple Speed Gear levels: Low, Medium, High, ReverseMotor/power wire size: 12 AWGProgrammable: YesRegenerative Capacity: YesSize: L110.5*W55*H30mm(Including Alu. Case)Power Switch Button: Red Features:1.Adopting CPU AT32F403ARCT7 with the structure of ARM Cortex-M4 allows CPU clock speed2.240MHz and the max PWM switching frequency 45KHz, which improves the motor RPM.3.Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different batteryvoltages and many control ways.4.Programmable via Flipsky VX4 remote(Firmware Version:VX4_V1.2)5.Supporting FOC with low working noise and smooth starting.6.Supporting Real-time data and fault alerts.7.Supporting adaptive variable PWM frequency control.8.Supporting sensor mode(HALL) and sensorless mode(IPDS, HFPI).9.Supporting control types: Current, Duty Cycle10.Protection functions: low and high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature and over current protection, battery over discharge protecting, motor over-temperature protection. Application Fields:Electric skateboard / Ebike / E-Scooter / Electric Motorc ycle / Robotics / FPV / RC Toys /Boat / Kayak etc Note: USB cable will be shipped randomly in black or white color.

Read more less