4IN1_8S80A_ESC Description： The 4IN1_8S80A_ESC is a high-performance brushless electronic speed controller that supports an input of 4-8S lithium batteries and has a continuous current rating of 80A. It is widely applicable to FPV racing drones, multi-rotor drones, VTOL Fixed-wing UAV , etc.   4IN1_8S80A_ESC Parameters： Type: Brushless Motor Electronic Speed Controller Continuous Current: 80A Peak Current: 100A Weight of bare board (excluding capacitors): 12.5g   Weight of the ESC with heat sink (excluding capacitors): 17.9g±2g Size: 42.2 mm (L) × 43.8mm (W) × 7.4mm (H) Mounting hole spacing: 30.5*30.5mm Mounting aperture: 4mm (M4) Input Power Supply: 4S-8S LiPo Firmware Version: MAXKGO_4IN1_F421 Firmware Upgrade: Supports online upgrade via AM32.ca Communication Protocol: Dshot 300, Dshot 600, Servo PWM Signal Feedback: The TX telemetry feedback port can provide ESC voltage, current, temperature, motor speed and etc. Waterproof: Not support4IN1_8S80A_ESC Features： 1.MINI Size,MAX Power output. 2.Supports multiple protection functions: Low-voltage protection, over-temperature protection, motor stall protection, low-speed protection. 3.Equipped with high-performance ARM 32-bit Cortex-core MCU, operating frequency up to 120 MHz. 4.Provides paddle stuck (locked-rotor) protection function for multi rotor aircraft. 5.Supports to upgrade firmware via Betaflight, Passthrough, single-wire UART or Arduino. 6.Supports parameter configuration via the AM32.ca web configuration tool. 7.Supports Servo PWM and Dshot300/600 communication Protocol. 8.Supports EDT (Extended Dshot Telemetry). Complete telemetry data can be obtained via signal wire. 4IN1_8S80A_ESC Application Fields： Multi-rotor Drone Fixed-wing Model Aircraft FPV drone Multi-rotor drone VTOL Fixed-wing UAV   Package Content： Option 1: 4IN1_8S80A_ESC *18pin Double-Ended Terminal Wire *1（25mm SH1.0） 8Pin single-head terminal wire  *1 (60mm, SH1.0 terminal) 8Pin empty terminal head  * 1 (SH1.0 terminal) Vibration Damping Ball *5（M3*8） Fixing nuts (M3)*5 Solid Capacitor *1（35V 820μF）XT60 Male Connector *1 Black Power Cable*1（12AWG，120mm） Red Power Cable *1（12AWG，120mm） Option 2: 4IN1_8S80A_ESC*1 heat sink  *1 (installed at the esc before shipment) 8Pin double-ended terminal wire *1 (25mm, SH1.0 terminal) 8Pin single-head terminal wire x 1 (60mm, SH1.0 terminal) 8Pin empty terminal head x 1 (SH1.0 terminal) Damping ball *5 (M3 * 8) Fixing nuts (M3)*5 Solid capacitor *1 (35V 820μF) XT60 male connector *1 4IN1_8S70A_ESC Application Fields： Multi-rotor Drone Fixed-wing Model Aircraft Mountings： 4IN1_8S70A_ESC *18pin Double-Ended Terminal Wire *1（25mm SH1.0）Vibration Damping Ball *5（M3*8）Solid Capacitor *1（35V 820μF）XT60 Male Connector *1 Black Power Cable*1（12AWG，120mm） Red Power Cable *1（12AWG，120mm）Sealed plastic box

Read more less

5-12S 80A_ESC Description： 5-12S 80A ESC is a high-performance brushless electronic speed controller (ESC) that supports 5-12S LiPo battery input and delivers a continuous current rating of up to 80A. It is widely used in FPV racing drones, multi-rotor drones, fixed-wing aircraft, RC cars, RC boats, and other model applications.   5-12S 80A ESC Specifications Type: Brushless Motor Electronic Speed Controller (ESC) Continuous Current: 80A Burst Current: 100A Weight (without capacitor): Net Weight 19.2g ± 2g Dimensions: 46.4mm (Length) × 24.8mm (Width) × 9.6mm (Height) Input Power: 5S–12S LiPo Battery Firmware Version: AM32_MAXKGO_F421 Firmware Upgrade: Supports online firmware updates via AM32.ca Communication Protocols: Dshot300, Dshot600, Servo PWM Signal Feedback: The TX telemetry port supports ESC data feedback, including voltage, temperature, and motor RPM (current sensing is not supported) BEC: No BEC output Cooling Fan: No built-in cooling fan Water Resistance: Not waterproof; only resistant to light splashes 5-12S 80A ESC Features MINI Size, MAX Power OutputCompact design with high-performance power output, providing an excellent balance between size and performance. Multiple Protection Functions: Low Voltage Protection Over Temperature Protection Motor Stall Protection Low-Speed Protection Equipped with a high-performance ARM 32-bit Cortex-core MCU with a processing frequency of up to 120MHz. Designed with stall protection for RC cars and crawler vehicles to prevent damage caused by motor blockage. Provides propeller jam (stall) protection for multi-rotor drones, improving flight safety and ESC reliability. Supports firmware upgrades via: Betaflight Passthrough Single-wire UART Arduino Supports parameter configuration through the AM32.ca online configuration tool. Supports Servo PWM and Dshot300 / Dshot600 protocols. Supports EDT (Extended Dshot Telemetry), allowing full telemetry data transmission through the signal wire. Equipped with sine wave startup mode, providing smoother and more responsive startup performance for RC cars and crawler vehicles. 5-12S 80A ESC Applications Multi-rotor drones Fixed-wing model aircraft RC cars RC boats Package Contents Package 1 5-12S 80A ESC × 1 Heat Shrink Tubes × 5 Electrolytic Capacitor × 1 (63V 680μF) 2-Pin Dupont Cable × 1 (33cm) Package 2 5-12S 80A ESC × 1 Heat Shrink Tubes × 5 Electrolytic Capacitor × 1 (63V 680μF) 2-Pin Dupont Cable × 1 (33cm) 3-Pin Dupont Cable × 1 (33cm) XT90 Male Connector × 1 Black Power Wire × 1 (12AWG, 120mm) Red Power Wire × 1 (12AWG, 120mm)

Read more less

Description The 5-12S 200A MINI ESC is a high-performance brushless electronic speed controller (ESC) that supports 5-12S LiPo battery input and provides a continuous current rating of up to 200A. Designed for high-power applications, it is widely used in FPV racing drones, multi-axis UAVs, fixed-wing model aircraft, RC cars, RC boats, agricultural spraying drones, electric cruise UAVs, firefighting drones, and other industrial drone platforms. 5-12S 200A MINI ESC Specifications Type: Brushless Motor Electronic Speed Controller (ESC) Continuous Current: 200A Burst Current: 250A Weight: Net Weight 144g ± 5g Dimensions: 84mm (Length) × 43mm (Width) × 28mm (Height) Input Power: 5S–12S LiPo Battery Firmware Version: MAXKGO_12S_F421 Firmware Upgrade: Supports online firmware updates via AM32.ca Communication Protocols: Dshot300, Dshot600, Servo PWM Telemetry Feedback: The TX telemetry port supports ESC data feedback, including voltage, current, temperature, motor RPM, and other operating parameters BEC: No BEC output Cooling Fan: No built-in cooling fan Water Resistance: Not waterproof; only resistant to light splashes 5-12S200A MINI ESC Features Feature Category Description Compact Design MINI Size Protection Functions Supports multiple protection functions: Low-voltage protection, over-temperature protection, motor stall protection, low-speed protection MCU Performance High-performance ARM 32-bit Cortex-core MCU with an operating frequency of 120 MHz RC Car Support Stall protection for RC cars and crawlers Drone Protection Stuck rotor protection for multi-rotor drones Firmware Upgrade Firmware upgradable via Betaflight passthrough, single wire serial, or Arduino Web Configurator Web configurator at am32.ca Protocol Support Supports Dshot 300, Dshot 600 and Servo PWM communication protocol Telemetry Support EDT for full Dshot telemetry via signal wires Smooth Startup Sinusoidal startup mode for smoother starting on RC cars and crawlers 5-12S 200A MINI ESC Applications Multi-axis UAVs Fixed-wing model aircraft RC cars RC boats Agricultural spraying drones Electric cruise UAVs Firefighting drones Package Contents Package 1 5-12S 200A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) Package 2 5-12S 200A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) 3-Pin Dupont Cable × 1 (33cm) XT90 Male Connector × 1 Positive & Negative Power Wires × 1 (8AWG / 200mm)  

Read more less

Description The 5-12S 120A ESC is a high-performance brushless electronic speed controller (ESC) that supports 5-12S LiPo battery input and delivers a continuous current rating of up to 120A. It is widely used in FPV racing drones, multi-axis UAVs, fixed-wing model aircraft, multi-rotor aircraft, RC cars, RC boats, and other high-power RC applications. 5-12S 120A ESC Specifications Type: Brushless Motor Electronic Speed Controller (ESC) Continuous Current: 120A Burst Current: 150A Weight: 93g ± 5g Dimensions: 78.8mm (Length) × 34.6mm (Width) × 21.8mm (Height) Input Power: 5S–12S LiPo Battery Firmware Version: MAXKGO_12S_F421 Firmware Upgrade: Supports online firmware updates via AM32.ca Communication Protocols: Dshot300, Dshot600, Servo PWM Telemetry Feedback: The TX telemetry port supports ESC data feedback, including voltage, current, temperature, motor RPM, and other telemetry information BEC: No BEC output Cooling Fan: No built-in cooling fan Water Resistance: Not waterproof; only resistant to light splashes 5-12S 120A ESC Features MINI Size DesignCompact structure with powerful performance, offering an excellent balance between size and power output. Multiple Protection Functions: Low Voltage Protection Over Temperature Protection Motor Stall Protection Low-Speed Protection Equipped with a high-performance ARM 32-bit Cortex-core MCU with a processing frequency of up to 120MHz. Supports AM32 firmware, with online configuration and firmware updates through AM32.ca. Supports Dshot300, Dshot600, and Servo PWM protocols, providing compatibility with various flight controllers and RC platforms. 5-12S 120A ESC Applications Multi-axis drones Fixed-wing model aircraft Multi-rotor aircraft RC cars RC boats Package Contents Package 1 5-12S 120A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) Package 2 5-12S 120A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) 3-Pin Dupont Cable × 1 (33cm) XT90 Male Connector × 1 Positive & Negative Power Wires × 1 (8AWG / 200mm)

Read more less

5-14S 100A ESC Description The 5-14S 100A ESC is a high-performance brushless electronic speed controller (ESC) that supports 5-14S LiPo battery input and provides a continuous current rating of 100A. It is widely used in FPV racing drones, multi-rotor UAVs, fixed-wing model aircraft, RC cars, RC boats, agricultural spraying drones, and other high-performance RC applications. 5-14S 100A ESC Specifications Type: Brushless Motor Electronic Speed Controller (ESC) Continuous Current: 100A Burst Current: 130A Weight: Net Weight 72g ± 5g Dimensions: 68.5mm (Length) × 34mm (Width) × 24.5mm (Height) Input Power: 5S–14S LiPo Battery Firmware Version: MAXKGO_V1_F421 Firmware Upgrade: Supports online firmware updates via AM32.ca Communication Protocols: Dshot300, Dshot600, Servo PWM Telemetry Feedback: The TX telemetry port supports ESC data feedback, including voltage, current, temperature, motor RPM, and other operating parameters BEC: No BEC output Cooling Fan: No built-in cooling fan Water Resistance: Not waterproof; only resistant to light splashes 5-14S 100A ESC Features Mini Size, Powerful PerformanceCompact design with high power output, providing excellent performance for various RC applications. Multiple Protection Functions: Low Voltage Protection Over Temperature Protection Motor Stall Protection Low-Speed Protection Equipped with a high-performance ARM 32-bit Cortex-core MCU with a processing frequency of up to 120MHz. Stall Protection for RC Cars and CrawlersHelps prevent ESC damage caused by motor blockage during low-speed or high-load operation. Stuck Rotor Protection for Multi-Rotor DronesProvides protection against propeller blockage or sudden motor stoppage during flight. Flexible Firmware Upgrade SupportFirmware can be upgraded through: Betaflight Passthrough Single-wire Serial Arduino AM32 Web Configurator SupportSupports online parameter configuration through AM32.ca. Multiple Protocol CompatibilitySupports: Servo PWM Dshot300 Dshot600 EDT (Extended Dshot Telemetry) SupportEnables full Dshot telemetry feedback through the signal wire for real-time ESC monitoring. Sinusoidal Startup ModeProvides smoother startup performance for RC cars and crawlers, reducing vibration and improving control response. 5-14S 100A ESC Applications Multi-rotor drones Fixed-wing model aircraft RC cars RC boats Package Contents Package 1 5-14S 100A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) Package 2 5-14S 100A ESC × 1 Heat Shrink Tubes × 5 2-Pin Dupont Cable × 1 (33cm) 3-Pin Dupont Cable × 1 (33cm) XT90 Male Connector × 1 Positive & Negative Power Wires × 1 (10AWG / 200mm)

Read more less

Specifications :  Firmware: 5.2 (supporting firmware upgrade)  Continuous current: 150A; instantaneous current: 200A (values depend on the mounting and ambient temperature around the device!)  Voltage: 14V-52V ( Cells: 4-13S; safe for 4S to 12S, voltage spikes may not exceed 52V! )  BEC: 5V@1.5A; ERPM: 150000  Supported sensors: Sensorless Supported Modes: BLDC, FOC (sinusoidal)  Control Interface Ports: USB UART  Input Set Support: PPM, ADC, NRF, UART  Regenerative capacity: Yes Programmable: Yes   Power Wire: 8AWG 1200mm / Motor Wire: 8AWG 170mm   Size: 103.5x67.6x27.5mm(Including aluminum case)  Features:  1.Fully sealed with IP68 water-proof rate.  VESC ESC: based on vesc6, programmable via VESC_TOOL and support real-time data read.  2.6-layer 3oz special PCB plate with good heat dissipation, support rated current 150Amps. 3.Adopting CPU STM32F405 with the structure of ARM Cortex-M4 allows CPU clock speed.  4.Support three control modes: Current / Dutycycle / Speed.  5.Multiple protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection over 80 ℃.  6.Compact size with high efficiency: 103.5x67.6x27.5mm.  Wiring Diagram: 

Read more less

Click it MINI V6.8 Specifications :  Firmware:  vesc_tool_3.00 5.2 (supporting firmware upgrade) Continuous current: 100A; instantaneous current: 150A (values depend on the mounting and ambient temperature around the device!) Voltage: 14V-60V(Cells: 4-13S; safe for 4S-12S, voltage spikes may not exceed 60V! )  BEC: 5V@1.5A; ERPM: 150000 Support Hall Sensor: No, Sensorless Supported Modes: BLDC, FOC (sinusoidal) Control Interface Ports: USB, CAN, UART, IIC Input Set Support: PPM, ADC, NRF, UART Regenerative capacity: Yes Programmable: Yes Motor wire: 10AWG; Power cable: 8AWG Size: 64x43.5x34.7mm(Including heatsink) Features: Based on vesc6, programmable via VESC_TOOL and support real-time data read. Adopting CPU STM32F405 with the structure of ARM Cortex-M4 allows CPU clock speed.  Support three control modes: Current / Dutycycle / Speed. Protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection. Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160 Wiring diagram: MINI V6.8 Plus Specifications :  Firmware: 5.2 (supporting firmware upgrade) Continuous current: 150A; instantaneous current: 200A (values depend on the mounting and ambient temperature around the device!) Voltage: 14V-60V ( Cells: 4-13S; safe for 4S to 12S, voltage spikes may not exceed 60V! ) BEC: 5V@1.5A; ERPM: 150000 Supported sensors: ABI, HALL,AS5047,AS5048A Supported Modes: BLDC, FOC (sinusoidal) Control Interface Ports: USB, CAN, UART, IIC Input Set Support: PPM, ADC, NRF, UART Regenerative capacity: Yes Programmable: Yes Power Wire: 8.0mm bullets female X 2pcs Motor Wire: 8.0mm bullets female X 3pcs Size: 92.7x68x31.5mm(Including aluminum case) Features: 1) Based on vesc6, programmable via VESC_TOOL and support real-time data read. 2) Adopting CPU STM32F405 with the structure of ARM Cortex-M4 allows CPU clock speed. 3) Support four control modes: Current / Dutycycle / Speed 4) Protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection. 5) Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160 Wiring diagram:  

Read more less

2670 Brushless ESC Product Description: (1) Adopting 32-bit high-performance processor STM32G071, with a working frequency of up to 64MHz and maximum support 128KHz motor PWM frequency.(2) PCB adopts 8-layer 3OZ immersion gold process, high-power MOS combined with metal heat sink, which can effectively dissipate heat under high current load and continue to work stably.(3) Supports multiple motion modes such as unidirectional, bidirectional, and braked motors.(4) Supports multiple protections such as low voltage protection, temperature protection, locked rotor protection, and current protection.(5) The ESC automatically detects the throttle signal when it is powered on, supports all Dshot signals, and also supports signal protocols such as PWM, Oneshot and Multishot.(6)BEC supports adjustable outputs of 5V/4A, 6V/4A, 7.2V/4A, 8.2V/4A, and 12V/3A, which can directly supply power to external devices such as receivers and servos, making the application of ESCs more extensive and flexible.(7) Visual programming parameter adjustment tool supports motor timing, throttle calibration, current detection, motor steering, telemetry signal and other settings.(8) Onboard RGB LED color light settings, multiple LED colors can be customized.(9) Widely used in FPV racing drone,multi-axis drones, fixed-wing, model ships, climbing vehicles, model cars and other scenarios. Parameters of 2670 Brushless ESC: Model  2670 Processor STM32G071 Input voltage DC 7V-25.2V（2-6S Lipo） Continuous current (good heat dissipation) 70A Maximum current  (good heat dissipation) 110A Support firmware BLHeli_32，AM32 BLHeli_32 firmware SEQURE_G071_01 AM32 firmware SEQURE_G071 Signal protocol Dshot (All), PWM, Oneshot, Multishot, etc. Programming parameter adjustment Support Throttle calibration Support Timing angle setting Support Current detection Support Telemetry signal Support Motor steering settings Support RGB LED color lights Support BEC (if any) 5V/4A，6V/4A，7.2V/4A，8.2V/4A，12V/3A adjustable Application scenarios FPV racing drones, multi-axis drones, fixed-wing  UAV, model ships, climbing vehicles, model cars, etc.

Read more less

Specifications :  Firmware: V1.5 and above (firmware update via Flipsky ESC Tool supported)Voltage: 14V-85V (safe for 4S-20S)Continuous current: 50V/400A; 75V/350A; 85V/300A (Values depend on the mounting, ambient temperature and air/water circulation around the device.)Peak Current: 800ABEC: 5V@1APower/Motor Wires: Integrated M6 terminalsProgrammable Tool: Flipsky ESC TOOLPWM Frequency Control: YESMultiple Speed Gear Limit Control: YES (UART / ADC)Regenerative Capacity: YESCommunication Ports: USB, CAN, UART, PPM, ADC/PASInput Signals Support: PPM, ADC, PAS, UART(compatible with FLIPSKY remote such as VX1, VX1Pro, VX2, VX3, VX3Pro, VX4Pro )Startup Modes Support: IPDS (sensorless), HFPI (sensorless), HALL (sensored), ENCODER(ABI Encoder，AS5047 Absolute Type Encoder SPI Port), OPEN(Sensorless Open-Loop Startup)Traction Control: YESMultiple Speed Gear levels: Low, Medium, High, ReverseSwitch Support: Power on/off button switch or key switchSize:L190*W109.1*H55.8(with aluminum enclosure) Features: 1.Adopting ARM Cortex-M4 structure with the max 240MHz , improves PWM switching frequency and the motor RPM.2.Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different battery voltages and multiple control methods.3.Programmable via Flipsky remote controller VX4Pro(remote firmware version: VX4Pro_V1.1 and above)4.Supporting motor FOC with low working noise and smooth starting.5.Supporting Real-time data and fault alerts.6.Supporting adaptive variable PWM frequency control.7.Supporting sensor mode(HALL,ENCODER) and sensorless mode(IPDS, HFPI,OPEN).8.Supporting control types: Current, Duty Cycle, Speed Control, Position Control.9.Supporting multiple types of motor temperature sensors such as NTC-10k-25℃, NTC-10K-100℃, PT1000, PTC-1K-100℃, KTY, etc.10.Protection functions: low and high voltage protection, motor over-temperature protection, MOSFET over-temperature and over current protection, battery over discharge protection.11.Integrating power of 12V(3pcs) to provide power for external devices(headlight, brake light, horn, etc.) with two groups normally open and one controlled by brake signal. (Note: maximum output current:4A)12.Supporting brake signal to cut off ESC output. Wire Connection:

Read more less

Speciation: Size:L107mm*W103mm*H18.5mmVoltage:14-84V (4-20S safey)Current:continuous max 100A single,dual continuous max 200A,values depend on the mounting  and ambient temperature around the device!BEC:5V@1ASupport BLDC square wave mode control and FOC sine wave modeFirmware: latest (firmware update supported)ERPM:150000Control Interface Ports:USB,CAN,UARTSupported Sensors:ABI，HALL，AS5047，AS5048AInput Set Support:PPM，ADC，NRF,UARTWire Size: 12AWGProgrammable: YesRegenerative Capacity: Yes Warm tips: Phase filering is not available for Flipsky ESC75100 and 75200!Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface. Wire Connection:

Read more less

Specs: 75100: 75100 Pro: Size: L103mm*W58mm*H27.7mm Voltage:14-84V (4-20S) Current:100A Continuous,burst 120A BEC:5V@1.5A Support BLDC square wave mode control and FOC sine wave mode Firmware: latest (firmware update supported) ERPM:150000 Control Interface Ports:USB,CAN,UART Supported Sensors:ABI，HALL，AS5047，AS5048A Input Set Support:PPM，ADC，NRF,UART Wire Size: 10AWG(75100 Pro) Programmable: Yes Regenerative Capacity: Yes Newly upgraded: Change connection wires from 12Awg to 10Awag. More sensitive temperature detection function Integrated bluetooth module design Size & design upgraded Warm tips: Phase filering is not available for Flipsky ESC75100 and 75200!Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface.Here below video and blog links FYI. Wire Connection: 75100: 75100 Pro:

Read more less

Specifications: Voltage:14-84V( safe for 3-20S) Continuous Current : 50V/350A,75V/250A Max Current :800A Supported sensors: ABI, HALL, AS5047,AS5048A EPRM:150000 Size:200*94.6*50mm((Including the height of water pipes and electrolytic capacitors) Warm tips: Phase filering is not available for Flipsky ESC75100 and 75200 ! Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface. Feature: 1.Regenerative braking 2.The CPU adopts the 32F405 with the main frequency of 168MHz and the Cortex-M4 architecture with DSP function; 3.Sensored or sensorless operation + hybrid mode 4.Configurable RPM-, current-, voltage- and power limits 5.Input source: PPM, ADC, NRF,UART,PAS 6.Communication ports: USB, CAN, UART,SPI,IIC 7.Throttle curve and ramping for all input sources 8.Seamless 4-quadrant operation 9.Motor revolution, ampere hour, watt hour counting 10.Real-time data analysis and readout through the communication port. 11.Adjustable protection against: 12.Low input voltage 13.High input voltage 14.High motor current 15.High input current 16.High regenerative braking current (separate limits for the motor and the input) 17.High RPM (separate limits for each direction) 18.Digital VCC and analog VCC are produced by different voltage regulators respectively to make the system AD conversion more accurate. 19.Motor wire: 8AWG 20.Power cable: 8AWG 21.Waterproof level(with water cooling enclosure):IP67 Wire Connection:

Read more less